China Factory Reorder Statistics (2026): 20+ Data Points on Dye Lots, Fabric Availability, and Repeat-Order Consistency
One Chinese knit-fabric maker sets a 200 kg minimum per colour combination, so a reorder in a new shade restarts the minimum. That is the part of reordering most brands miss: the second order is not a copy of the first, because quantity, colour and fit rules all attach to the details you approved the first time.
200 kg
minimum per colour combination at one Chinese knit-fabric maker for custom tie-dye knit, so a reorder in a new shade restarts the minimum (Runtang Textile, single-supplier terms).
The same fabric takes 25-45 days for bulk production (Runtang Textile, 2026). ASTM D2616 grades colour difference with 9 pairs of gray standards built for differences under 15 CIELAB units, and large US fashion companies now source from 49 countries, up from 46 (USFIA). Reorder consistency itself has no institutional numeric benchmark, and we say so wherever a number would otherwise be invented.
We aggregated 20 data points from AATCC, ASTM International, ISO and BSI, USFIA’s 2026 Benchmarking Study, Runtang Textile and other primary sources. Reorder consistency has no institutional numeric benchmark, so we cover the standards that define ‘same colour’ and ‘same fit’ and label supplier figures as single-source. Because the verified pool is small, this article has fewer data points than our usual range.
We get asked how to reorder from a China factory by almost every brand that has sold through a first run. The honest answer is that consistency is something you specify in writing before the reorder PO, not something you hope the factory remembers. The sections below cover the market backdrop, what ‘same colour’ means in standards terms, per-colour minimums and dye lots, fit and tech pack versioning, and how to check bulk against the approved standard.
Key Takeaways
- 49 in 2026, up from 46 in 2025: Countries sourced from by respondents (USFIA).
- ~65%: Share sourcing from 10+ countries (USFIA).
- 9 pairs: Neutral gray standard pairs in the ASTM gray scale (ASTM International).
- Under 15 CIELAB units (small to moderate differences): Colour difference range the gray scale is intended for (ASTM International).
- CMC(l:c); tolerance depends on end-use closeness of match: Formula used by ISO 105-J03 to calculate colour difference (BSI / ISO).
- 200 kg per colour combination: MOQ for custom tie-dye knit fabric (Runtang Textile).
- 25-45 days: Bulk production time for custom tie-dye knit fabric (Runtang Textile).
- MCQ 100 pcs per colour; MOQ 300 pcs per style: Example minimum colour quantity (MCQ) vs MOQ (Prototype.fashion).
- 500-1,000 pcs per style and per colour: Typical Vietnamese export-factory minimum (Cosmo Sourcing).
- Sizes 00-20: Size range of ASTM D5585 body measurement tables (adult female Misses) (ASTM International).
1. Why the Second Order Is Harder Than the First: The Sourcing Backdrop
Reorders happen in a market that is spreading out. Large US buyers now source from 49 countries, up from 46 a year earlier, and roughly 65% of them use ten or more, so the factory you reorder from is one of many a large buyer could move volume between.
Expected sourcing growth is under 5%, which means little new capacity pressure to excuse a slipped second lot. The colour, fit and fabric standard therefore has to be settled before the reorder PO goes out. If your first order was small, start with our clothing MOQ benchmarks by garment type to see what minimums apply to a repeat run.
None of these figures measures factory reorder lead time. We found no institutional source that does, so this article does not quote one.
We found no institutional source that measures factory reorder lead time, so anything quoted without a named factory behind it deserves suspicion.
| Metric | Value | Source | Tier |
|---|---|---|---|
| US fashion companies surveyed (Apr-Jun 2026) | 30 companies; ~80% have 1,000+ employees Large-company sample; not a small-brand benchmark. |
USFIA | 1 |
| Countries sourced from by respondents | 49 in 2026, up from 46 in 2025 | USFIA | 1 |
| Share sourcing from 10+ countries | ~65% Applies to the large (1,000+ employee) companies in the sample. |
USFIA | 1 |
| Expected sourcing growth | Most expect modest growth, below 5% (value or volume) | USFIA | 1 |
The USFIA sample is 30 large US companies; read it as the environment around a small brand’s reorder, not as a small-brand benchmark.
2. What ‘Same Colour’ Actually Means: Gray Scales and Colour-Difference Standards
‘Match the approved shade’ is not a measurement until someone names the method. AATCC EP1-2025 rates overall colour change visually and says outright that lightness, chroma and hue are not quantified.
ASTM D2616 uses 9 pairs of gray standards built for differences under 15 CIELAB units, which is a small-to-moderate range, not a tight one. ISO 105-J03 calculates colour difference with CMC(l:c), so a delta E quoted without its formula is not comparable to another factory’s number.
Write the method, the light source and the limit into the tech pack, and keep the approved physical swatch as the reference. We found no standards body that publishes a single pass/fail delta E for apparel; the limit is agreed between buyer and supplier for the end use.
A shade standard is a method plus a limit, not a colour name.
| Metric | Value | Source | Tier |
|---|---|---|---|
| Gray scale for colour change: what it quantifies | Visual rating of overall colour change; lightness, chroma and hue may be noted but are not quantified | AATCC | 1 |
| Neutral gray standard pairs in the ASTM gray scale | 9 pairs Verified on the D2616-12 text via the iTeh mirror; later 2019 edition not fetched. |
ASTM International | 1 |
| Colour difference range the gray scale is intended for | Under 15 CIELAB units (small to moderate differences) Figure appears in the standard’s Introduction (D2616-12 text). |
ASTM International | 1 |
| Formula used by ISO 105-J03 to calculate colour difference | CMC(l:c); tolerance depends on end-use closeness of match Standard defines the calculation, not a pass/fail limit. |
BSI / ISO | 1 |
We found no standards body that publishes a single pass/fail delta E for apparel; the limit is agreed between buyer and supplier for the end use. ASTM D2616 figures are verified against the D2616-12 text.
3. Fabric Availability and Minimums: Per-Colour Quantities When You Reorder
Quantity rules attach to the colour, not the style. One Chinese knit-fabric maker states 200 kg per colour combination for custom tie-dye knit, with 25-45 days for bulk. Prototype.fashion shows the split between a 100-piece minimum colour quantity and a 300-piece order minimum. A Vietnam sourcing agent puts typical factory minimums at 500-1,000 pieces per style and per colour.
At NewWay the MOQ is per colour: 100 pcs per colour for dresses, sportswear and plus-size in stock fabric, 300 pcs per colour for knitwear in stock yarn, and 1,000 pcs for custom-dyed fabric or yarn. A style reordered in three colours is therefore 300 pcs at the stock-fabric tier. The mechanics are covered in fabric MOQ is per colour, not per style.
For any custom-dyed colour, confirm in writing before the reorder whether it counts as a new dye lot and which minimum applies.
Ask the question before the reorder PO: is this colour a repeat or a new dye lot?
| Metric | Value | Source | Tier |
|---|---|---|---|
| MOQ for custom tie-dye knit fabric | 200 kg per colour combination Manufacturer’s own stated terms; tie-dye specific, not a general knit-fabric benchmark. |
Runtang Textile | 1 |
| Bulk production time for custom tie-dye knit fabric | 25-45 days One manufacturer’s own process stage; tie-dye specific. |
Runtang Textile | 1 |
| Example minimum colour quantity (MCQ) vs MOQ | MCQ 100 pcs per colour; MOQ 300 pcs per style Single-supplier policy (Black Label custom manufacturing), not an industry standard; the supplier says it may change. |
Prototype.fashion | 1 |
| Typical Vietnamese export-factory minimum | 500-1,000 pcs per style and per colour Sourcing agent’s statement about Vietnam, not China; comparison only. |
Cosmo Sourcing | 1 |
Runtang and Prototype figures are single-supplier terms and the Cosmo Sourcing figure covers Vietnam. They illustrate how minimums are structured; they are not China-wide benchmarks.
4. Fit and Construction Drift: Size Standards and Tech Pack Version Control
Standards say what a size 12 body measures. They do not say what your size 12 garment measures. ASTM D5585 covers sizes 00-20 for Misses and D6960 covers 14W-40W for plus, with D5585 pointing to ISO 3635 for size designation.
Your garment’s own measurements live in your graded spec, and that file’s history is what keeps the second order aligned with the first. See our guide to tech pack costs and what to include.
One PLM vendor (Wave PLM) reports a convention of version IDs like v1.0, v1.1 and v2.0 per iteration, with factories receiving only versions cleared internally. This is a single vendor’s guidance and the original source is unverified. We found no quantitative data on fit drift between repeat orders.
On a reorder, send the factory the approved version number, not ‘the latest file’.
| Metric | Value | Source | Tier |
|---|---|---|---|
| Size range of ASTM D5585 body measurement tables (adult female Misses) | Sizes 00-20 Body measurement baseline, not a garment fit specification. |
ASTM International | 1 |
| Size range of ASTM D6960 plus-size body measurement tables (current revision) | Sizes 14W-40W (2004 edition covered 14W-32W) Range confirmed via ASTM jurisdiction listing and secondary standards sites; some storefronts still show stale ranges. |
ASTM International | 2 |
| International size designation standard cross-referenced by ASTM D5585 | ISO 3635 (size designation of clothes: definitions and body measurement procedure) Non-numeric cross-reference. |
ASTM International | 1 |
| Tech pack version ID convention | v1.0, v1.1, v2.0 per iteration; send factories only versions cleared by internal approval Vendor blog guidance, single vendor, original source unverified. A PLM system can prompt review of BOM, AQL criteria and factory comments; the page does not say it does so automatically. |
Wave PLM | 3 (flagged) |
The ASTM tables are body measurement baselines, not garment fit specifications. Version-control guidance is from a PLM vendor.
5. Checking Bulk Against the Approved Standard: Sampling, AQL and Colour Variance
Inspection only protects a reorder if it compares bulk to the approved standard, not to the factory’s own judgement. ISO 2859-1 was reissued as Edition 3 in 2026, and its sampling plans work with whatever AQL levels you put in the contract.
The common apparel defaults of 0 critical, 2.5 major and 4.0 minor are widely reported, but their original source is unverified (a PLM vendor states them) and they are not part of the standard. One vendor guide classes unacceptable colour variance from the approved shade as a major defect, and AATCC EP9-2025 is the current visual assessment procedure.
At NewWay, inspection runs in two layers: in-line quality control at partner factories, then a second inspection at our own facility before packing. Bulk production runs about 30 days after PP sample confirmation. For a reorder, confirm timing per order, because we do not publish a fixed reorder lead time.
Inspect against the approved sample, not against the previous shipment.
| Metric | Value | Source | Tier |
|---|---|---|---|
| Current edition of ISO 2859-1 (attribute sampling) | Edition 3, published 2026 (replaces the 1999 edition and Amd 1:2011) Edition corroborated by ISO listing text, AFNOR and EVS. |
ISO | 2 |
| Common apparel AQL defaults (critical / major / minor) | 0 / 2.5 / 4.0 Widely reported but original source unverified: a PLM vendor blog states it as the default; not part of ISO 2859-1. Set levels in your own contract. |
Wave PLM | 3 (flagged) |
| Colour variance between approved shade and production run | Classed as a major defect Vendor blog guidance, single vendor, non-numeric. |
Wave PLM | 3 (flagged) |
| AATCC visual colour-difference assessment procedure | EP9-2025 is the current edition | AATCC | 1 |
AQL defaults and the defect classification are vendor-blog statements (Tier 3-flagged); set levels per contract. We do not claim specific delta E thresholds or defect rates for NewWay.
Summary: All Data Points in One Table
Tier 1 is a primary source (standards body, official report or a supplier’s own stated terms). Tier 2 is a primary source corroborated by listings. Tier 3 (flagged) is vendor-blog guidance whose original source we could not verify, kept only where a section needed it.
| Metric | Value | Source | Tier |
|---|---|---|---|
| Countries sourced from by respondents | 49 in 2026, up from 46 in 2025 | USFIA | 1 |
| Share sourcing from 10+ countries | ~65% Applies to the large (1,000+ employee) companies in the sample. |
USFIA | 1 |
| Gray scale for colour change: what it quantifies | Visual rating of overall colour change; lightness, chroma and hue may be noted but are not quantified | AATCC | 1 |
| Neutral gray standard pairs in the ASTM gray scale | 9 pairs Verified on the D2616-12 text via the iTeh mirror; later 2019 edition not fetched. |
ASTM International | 1 |
| Colour difference range the gray scale is intended for | Under 15 CIELAB units (small to moderate differences) Figure appears in the standard’s Introduction (D2616-12 text). |
ASTM International | 1 |
| Formula used by ISO 105-J03 to calculate colour difference | CMC(l:c); tolerance depends on end-use closeness of match Standard defines the calculation, not a pass/fail limit. |
BSI / ISO | 1 |
| MOQ for custom tie-dye knit fabric | 200 kg per colour combination Manufacturer’s own stated terms; tie-dye specific, not a general knit-fabric benchmark. |
Runtang Textile | 1 |
| Bulk production time for custom tie-dye knit fabric | 25-45 days One manufacturer’s own process stage; tie-dye specific. |
Runtang Textile | 1 |
| Example minimum colour quantity (MCQ) vs MOQ | MCQ 100 pcs per colour; MOQ 300 pcs per style Single-supplier policy (Black Label custom manufacturing), not an industry standard; the supplier says it may change. |
Prototype.fashion | 1 |
| Typical Vietnamese export-factory minimum | 500-1,000 pcs per style and per colour Sourcing agent’s statement about Vietnam, not China; comparison only. |
Cosmo Sourcing | 1 |
| Size range of ASTM D5585 body measurement tables (adult female Misses) | Sizes 00-20 Body measurement baseline, not a garment fit specification. |
ASTM International | 1 |
| Size range of ASTM D6960 plus-size body measurement tables (current revision) | Sizes 14W-40W (2004 edition covered 14W-32W) Range confirmed via ASTM jurisdiction listing and secondary standards sites; some storefronts still show stale ranges. |
ASTM International | 2 |
| Tech pack version ID convention | v1.0, v1.1, v2.0 per iteration; send factories only versions cleared by internal approval Vendor blog guidance, single vendor, original source unverified. A PLM system can prompt review of BOM, AQL criteria and factory comments; the page does not say it does so automatically. |
Wave PLM | 3 (flagged) |
| Current edition of ISO 2859-1 (attribute sampling) | Edition 3, published 2026 (replaces the 1999 edition and Amd 1:2011) Edition corroborated by ISO listing text, AFNOR and EVS. |
ISO | 2 |
| Common apparel AQL defaults (critical / major / minor) | 0 / 2.5 / 4.0 Widely reported but original source unverified: a PLM vendor blog states it as the default; not part of ISO 2859-1. Set levels in your own contract. |
Wave PLM | 3 (flagged) |
| Colour variance between approved shade and production run | Classed as a major defect Vendor blog guidance, single vendor, non-numeric. |
Wave PLM | 3 (flagged) |
Methodology and Sources
Reorder consistency (dye lots, shade drift, fit drift, reorder lead time) has no institutional numeric benchmark. We started from standards bodies and primary reports, fetched each source where possible, corrected several candidate figures that did not match the source text, and dropped figures we could not verify. Supplier and vendor figures are labelled as single-source examples. Because the verified pool is small, this article has fewer data points than our usual range.
- ASTM D2616 figures were verified on the D2616-12 text via a mirror; a 2019 edition exists and was not fetched.
- ASTM D5585-21 (2021 edition) is the current edition per the ASTM store listing; used for the size range 00-20 and the ISO 3635 cross-reference.
- ASTM D6960/D6960M-16(2023) is the current edition (2023 reissue of the 2016 revision) per ASTM listings; it covers 14W-40W, superseding the 2004 edition’s 14W-32W.
- ISO 105-J03 is the 2009 edition (current per BSI).
- Most recent available data: AATCC EP1-2025 and EP9-2025, ISO 2859-1:2026, USFIA 2026.
- Supplier and vendor figures (Runtang Textile, Prototype.fashion, Cosmo Sourcing, Wave PLM) are single-source examples and are labelled as such in the tables above.
- NewWay figures (per-colour MOQ tiers, dual-layer QC, about 30 days of bulk after PP sample confirmation) are our own published production terms.
Full source list – 13 documents
- USFIA, 2026 USFIA Fashion Industry Benchmarking Study
- AATCC, AATCC EP1-2025, Gray Scale for Color Change
- ASTM International, ASTM D2616, Evaluation of Visual Color Difference With a Gray Scale
- BSI / ISO, BS EN ISO 105-J03:2009, Calculation of colour differences
- Runtang Textile, Leading Knit Fabric Manufacturer (tie-dye batch repeatability)
- Prototype.fashion, Our Minimum Order Quantities
- Cosmo Sourcing, Low MOQ Clothing Manufacturers in Vietnam
- ASTM International, ASTM D5585-21, section 4.1
- AATCC, AATCC EP9 Visual Assessment of Color Difference of Textiles
- ASTM International, ASTM D6960/D6960M-16(2023)
- ISO, ISO 2859-1:2026 Sampling procedures for inspection by attributes, Part 1
- Wave PLM, Tech Pack Version Control: How Apparel Brands Manage Revisions Without Chaos (Tier 3, flagged)
- Wave PLM, AQL Inspection in Apparel: How to Set Defect Thresholds and Catch Quality Issues Before They Ship (Tier 3, flagged)
Last updated: November 2026. We update this page quarterly.
Reordering a Style and Want the Colour to Match?
NewWay makes sweaters, dresses, sportswear and plus-size in Jiaxing, Zhejiang: 100 pieces per colour on stock fabric, 300 per colour on stock yarn, 1,000 for custom-dyed fabric or yarn, with in-line and final inspection before packing. Send us your approved sample, tech pack version and colour count and we will confirm what counts as a repeat and what counts as a new dye lot before you place the PO.
Talk to the Factory →